3dCustomizer.net: Design custom 3D Models for 3D printing

OpenSCAD Paste

$fn=100;

union() { //adding the ability to join to the box

//supports for the box
translate ([-25,-67.5,5]) 
       cube ([3,113,55], false);

translate ([-70.5,43,5]) 
       cube ([3,57,55], false);

translate ([70,43,5]) 
       cube ([3,57,55], false);
    
translate ([-149,43,5]) 
       cube ([298,3,55], false);
    
translate ([-149,-68,5]) 
       cube ([298,3,55], false);
   
translate ([-82.5,-99.5,5]) 
       cube ([3,33,55], false);

translate ([60,-99.5,5]) 
       cube ([3,33,55], false);

difference () { //start of difference so that every hole is removed from the box
    
//body of the box
difference () {
//outside of box
     translate ([0,0,0]) linear_extrude(height = 60, twist = 0, slices = 1) {
 
    offset(r = 15) {
      square([270,170],true);
     }  } 
//inside of box
     translate ([0,0,-3]) linear_extrude(height = 60, twist = 0, slices = 1) {
 
    offset(r = 15) {
      square([265,165],true);
     }  } }

//happ button holes are 27.5mm, holes should be 14.125 radius 
//holes for joystick mount call for 6mm holes originally
translate ([-120,28,0]) cylinder (h = 236, r=3.65, center = true, $fn=100); //top left hole
translate ([-44,28,0]) cylinder (h = 239, r=3.65, center = true, $fn=100); //top right hole
translate ([-120,-48,0]) cylinder (h = 235, r=3.65, center = true, $fn=100); //bottom left hole
translate ([-44,-48,0]) cylinder (h = 235, r=3.65, center = true, $fn=100); //bottom right hole
translate ([-82,-10,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //center hole for joystick, will make as wide as a happ button

//button layout         
translate ([-0,10,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //LP
translate ([-0,-30,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //LK
translate ([40,10,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //MP
translate ([40,-30,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //MK
translate ([80,10,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //HP
translate ([80,-30,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //HK
translate ([120,10,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //3P
translate ([120,-30,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //3K
     
//start buttons       
translate ([-0,70,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //P1 start
translate ([-40,70,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //Coin
translate ([40,70,0]) cylinder (h = 235, r=14.125, center = true, $fn=100); //P2 start    
     
} //end of difference so that every hole is removed from the box

} //closing the ability to join to the box